Parts & Accessories

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

Trainer Caps allow thru-axle bikes to be used with most wind, magnetic or fluid cycling trainers. Cold weather and short days are never far from a Minnesotan's mind so Wolf Tooth engineers created Trainer Caps to reduce barriers to winter workouts. Non-drive side axle caps are joined by drive-side plugs that can be installed or removed without tools to make the prospect of hopping on the trainer a little more bearable. - Compatibility: Wolf Tooth Rear Axles (not compatible with rear axles from other manufacturers) - Plug has O-ring retention – no tool required

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum Not compatible with RS-1 fork

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

TCS Max-Flow Tubeless Valves feature an insert-compatible base, increased bore diameter, an integrated valve core remover, and an ergonomically designed nut that allows riders to properly tighten down the valve without the use of a tool. TCS Max-Flow Tubeless Valves feature a castellated base for multi-directional air flow out the sides, therefore preventing the airflow restriction that can happen when a tire insert is pushed up against a traditional valve opening. Insert Compatible Allows optimal air flow with inserts. Valve Core Removal Cap No need for pliers with a valve core remover in the cap! Fluted Easy-Grip Nut Ergonomic shape allows for hand tightening. D-Ring Rubber Grommet Protects the rim from damage. Universal Presta Valve Core Easily source replacements.

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 34mm

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm

You know that feeling when you're just rippin' along and you hear the dreaded psssssssssssss sound from your tire? Well have no fear the TCS Tire Plug kit is here. It's easy to use and will get you back on two wheels in no time. More time for miles of smiles, rather than expletives on the side of the road or trail. Yea, we have all been there. The TCS Tire Plug Kit uses durable "Rocket" anchors (because they look like tiny rockets) that stay in your tire and hold the plug in place. You will not lose a plug. The anchor will hold it in place like a ship at dock. But wait... there's more... You can reuse the anchors when you're all done. It's like a treasure chest when you need to swap-out your tires. The Rocket Plug Kit also features an 'Extra Hand' tool under the smaller cap. If you haven't pre-loaded the Rocket, the Extra Hand will temporarily plug the hole and take the pressure off while you prepare your Rockets and plugs. We went through a lot of arguments at WTB to get this thing dialed and man, we are so stoked on how it turned out. We hope you like it as much as we do. REUSABLE "ROCKET" ANCHORS Rocket anchors rotate once pushed into the tire and physically prevent the plug from pulling back through the tire when running higher pressure or through heavy cornering like traditional plugs can. Oh, we tried to pull it through, and we were holding up e-bikes from the plug. The anchor remains fixed in place until it’s removed from the inside of the tire and put back in the tool for future use. Reusable and Recyclable! Win, win! EXTRA HAND The Extra Hand (because who couldn't use an extra hand every once and a while) stopper can be pushed into the puncture to temporarily stop any loss of air while a rider determines how many tire plugs are needed and prepares to seal it. The Extra Hand can also be used as a reamer to create a more uniform hole for the tire plugs to seal. COMPACT AND LIGHT The TCS Rocket Tire Plug Kit is CNC’d from 6061 aluminum alloy with an integrated extra hand tool and plunger. It also has internal storage for four anchors (two large and two small included), and fifteen 1.5mm diameter tire plugs. Ready to Launch Rocket anchors can be preloaded with 1-4 tire plugs depending on the terrain and size of punctures riders typically encounter. Preloaded Rocket anchors are then placed on the plunger, ready to launch the moment a puncture occurs. The clock is ticking! TCS Tubeless TCS (Tubeless Compatible System) is WTB's standardized tubeless system. When you do get a puncture with a tubeless tire with sealant inside, this is a great way to fix it.

Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)

Surly Rim Strips have one job and they do it well. They cover the cutouts in your rim and — if you're running a tube — they protect it from spoke heads and other sharp matter (okay, so maybe they have TWO jobs but they do them both really well.) Rim strips are crucial and should be used with all Surly rims. Ours come in an array of colors so you can really "express yourself." Surly Rim strips are available in two different materials: PVC and Nylon. PVC is great if you plan on only running tubes. However, if there's any part of you that wants to try this tubeless thing you've been hearing about, Nylon strips are just the ticket. They're thinner and offer minimal stretch so they stay put and lay nicely inside the rim to provide a secure seal. Plus, they're lighter which we all know means you'll go faster… maybe.

- Converts Schrader rims to Presta - Rubber - Sold individually

- Shell: 8mm flanged axle nut - Flanged

- For square taper and flanged. - Fits most cartridge BBs - Shell: 8mm Flanged axle bolt

Replacement Axle nuts for three speed Sturmey Archer hubs.

- Replacement adjustable nut for three-speed internal hubs.

- Steel end nut for QR skewers

• Rim strips for 20-inch fat bike rims • 80mm wide

Replace the loop that goes around your left chainstay to secure your coaster brake arm with this Sunlite replacement part. It's made of full stainless steel, and it includes a nylock nut, washer, and bolt.

Rubber rim strips for 24-inch diameter fatbike rims. - Sold individually

Replacement clear plastic spoke guard.

- Eady to install - Spoke mounted - 2 per set

- Replacement rear skewer - Spacing: 135mm - Material: Steel

- Fits all freewheel hubs - Will not fit Cassette hubs - Type: STD Plastic - Color: Clear

- Replacement steel quick release skewers

• Replacement aluminum quick release skewers

• Replacement aluminum quick release skewers